The author is making a few good pointers regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in this article in the next paragraphs.
Setting up a tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably difficult task. If the old bathtub is conveniently available, the project can relocate rapidly; if you need to open a wall to eliminate the old bathtub and place the brand-new tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old bathtub and embeded in the brand-new one. Make certain you have qualified yourself for the work as well as are comfortable trying it. As opposed to employing a specialist to take control of a halfway-completed task, it is much better to think about utilizing one prior to you start. Opportunities are you may need a professional plumber to make tube links.
This article will aid you set up a new bathtub in your shower room if you have actually currently acquired a brand-new tub as well as don't need to change the arrangement of your previous water system pipes.
Your tools and material checklist must comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic due to the limited access that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipes. As soon as the supply pipelines have been removed, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washing machines are in location in between the tap and the sink. Secure the faucet in position with the maker offered backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The former type needs to be linked to the tap finishes first, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Using the two wood boards under its feet, place the tub in the called for placement. The wooden boards are helpful in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and adjusting the feet on the bath tub up until the spirit level reviews level.
To mount faucets, fit the bottom of the outermost versatile tap port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the water system and also check all joints as well as new pipework for leaks and also tighten them if essential. Load the bathtub and likewise examine the overflow outlet and the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the tub needs to wait until the tub has been made use of a minimum of once as this will resolve it into its last placement.
Planning for the Installment
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to avoid stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness as well as feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and fittings. They are marketed in tubes and also cartridges, and also can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Remember to always fill up the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealant can fracture relatively early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily available on the market. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very involved in How to Install a Bathtub Yourself and I am hoping you enjoyed our piece. Sharing is good. Helping others is fun. Many thanks for your time invested reading it.
Reliable help, dial now.